Field Guide / ECSite Services Division

Anritsu Sweep & PIM — CommScope HL4RPV‑50‑CBAND

Created by Alec Chapman — Senior Project Engineer / Prepared for Cleveland Electric • Rev 2025-08-11

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Frequency Presets & Cable Library

Presets (edit per test plan)

Use	Band	Span	Notes
Sweep	Low	698–806 MHz	Adjust to carrier spec
Sweep	Mid/High	1710–2200 MHz	Split if needed
Sweep	C‑Band	3700–3980 MHz	Use project UL/DL
PIM	700	705/720 tones	IM3 near 690/735
PIM	AWS	1730/1755	IM3 near 1705/1780
PIM	PCS	1870/1895	IM3 near 1845/1920

Current Cable — HL4RPV‑50‑CBAND

Frequency	Loss (dB/100ft)
700 MHz	1.64
1700 MHz	2.68
1900 MHz	2.85
2100 MHz	3.01
3800 MHz	4.16

VF = 0.88. Loss values editable in tools below.

Cable Library (edit & use in calculators)

Select cable

Velocity Factor (VF)

Attenuation points (MHz,dB/100ft per line)

Calculators below use the selected cable. Values are stored in your browser (localStorage). Use “Reset library” if the loss estimator shows 0—this restores HL4 defaults.

HL4RPV‑50‑CBAND pre‑filled Other cables: fill VF + loss

Interactive tools

Loss Estimator (uses selected cable)

Run length (ft)

Frequency (MHz)

Length ↔ Delay

Length (ft)

One‑way delay (ns)

Uses VF from selected cable; defaults to HL4RPV‑50‑CBAND (0.88).

RL ↔ VSWR converter

Return Loss (dB)

VSWR

dBc ↔ dBm @ carrier power

Carrier power per tone (W)

PIM level (dBc)

PIM level (dBm)

Assumes two equal tones.

Troubleshooting — quick flow

Pan diagram

Mini‑map: drag the box to pan; tap the track to jump.

Tip: drag the slider or swipe sideways to pan the diagram.

References & manuals

Official public docs for the common handhelds your crews use.

Anritsu Site Master S331L — User Guide (PDF)
Anritsu Site Master S331E/S361E/S332E/S362E — User Guide (PDF)
Anritsu PIM Master MW82119B — User Guide (PDF)
Anritsu PIM Master MW82119B — Programming Manual (SCPI)
Keysight FieldFox — CAT (Cable & Antenna Test) Help
Keysight FieldFox Library — Manuals (all models)
Rohde & Schwarz Cable Rider ZPH — User Manual
VIAVI OneAdvisor 800 — Cable & Antenna Testing (Quick Ref)

Tip: keep offline copies of the PDFs on field tablets for bad coverage areas.

Interactive terminal — guided setup (revamped)

ecsite@field • bash

Tester

Task

Band

Data points

Include tips

Show best-practice tips

Verbose details

Include sub-steps & rationale

$ echo "Select tester, task, and band — then Generate."

Uses current cable from the Cable Library (VF & loss). Change it above in the Cable Library and regenerate.

Acceptance workbook

Field	Value
Site / Sector / Ant ID
Cable Profile	HL4RPV‑50‑CBAND (VF=0.88)
Run Length
DTF Max Distance
RL Limits
PIM Tone Power
PIM Limits
Notes

CSV export works locally in the browser—no server needed.

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Frequency Presets & Cable Library

Presets (edit per test plan)

Use	Band	Span	Notes
Sweep	Low	698–806 MHz	Adjust to carrier spec
Sweep	Mid/High	1710–2200 MHz	Split if needed
Sweep	C‑Band	3700–3980 MHz	Use project UL/DL
PIM	700	705/720 tones	IM3 near 690/735
PIM	AWS	1730/1755	IM3 near 1705/1780
PIM	PCS	1870/1895	IM3 near 1845/1920

Current Cable — HL4RPV‑50‑CBAND

Frequency	Loss (dB/100ft)
700 MHz	1.64
1700 MHz	2.68
1900 MHz	2.85
2100 MHz	3.01
3800 MHz	4.16

VF = 0.88. Loss values editable in tools below.

Cable Library (edit & use in calculators)

Select cable

Velocity Factor (VF)

Attenuation points (MHz,dB/100ft per line)

Calculators below use the selected cable. Values are stored in your browser (localStorage). Use “Reset library” if the loss estimator shows 0—this restores HL4 defaults.

HL4RPV‑50‑CBAND pre‑filled Other cables: fill VF + loss

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Frequency Presets & Cable Library

Presets (edit per test plan)

Use	Band	Span	Notes
Sweep	Low	698–806 MHz	Adjust to carrier spec
Sweep	Mid/High	1710–2200 MHz	Split if needed
Sweep	C‑Band	3700–3980 MHz	Use project UL/DL
PIM	700	705/720 tones	IM3 near 690/735
PIM	AWS	1730/1755	IM3 near 1705/1780
PIM	PCS	1870/1895	IM3 near 1845/1920

Current Cable — HL4RPV‑50‑CBAND

Frequency	Loss (dB/100ft)
700 MHz	1.64
1700 MHz	2.68
1900 MHz	2.85
2100 MHz	3.01
3800 MHz	4.16

VF = 0.88. Loss values editable in tools below.

Cable Library (edit & use in calculators)

Select cable

Velocity Factor (VF)

Attenuation points (MHz,dB/100ft per line)

Calculators below use the selected cable. Values are stored in your browser (localStorage). Use “Reset library” if the loss estimator shows 0—this restores HL4 defaults.

HL4RPV‑50‑CBAND pre‑filled Other cables: fill VF + loss

Interactive tools

Loss Estimator (uses selected cable)

Run length (ft)

Frequency (MHz)

Length ↔ Delay

Length (ft)

One‑way delay (ns)

Uses VF from selected cable; defaults to HL4RPV‑50‑CBAND (0.88).

RL ↔ VSWR converter

Return Loss (dB)

VSWR

dBc ↔ dBm @ carrier power

Carrier power per tone (W)

PIM level (dBc)

PIM level (dBm)

Assumes two equal tones.

Troubleshooting — quick flow

Pan diagram

Mini‑map: drag the box to pan; tap the track to jump.

Tip: drag the slider or swipe sideways to pan the diagram.

References & manuals

Official public docs for the common handhelds your crews use.

Anritsu Site Master S331L — User Guide (PDF)
Anritsu Site Master S331E/S361E/S332E/S362E — User Guide (PDF)
Anritsu PIM Master MW82119B — User Guide (PDF)
Anritsu PIM Master MW82119B — Programming Manual (SCPI)
Keysight FieldFox — CAT (Cable & Antenna Test) Help
Keysight FieldFox Library — Manuals (all models)
Rohde & Schwarz Cable Rider ZPH — User Manual
VIAVI OneAdvisor 800 — Cable & Antenna Testing (Quick Ref)

Tip: keep offline copies of the PDFs on field tablets for bad coverage areas.

Interactive terminal — guided setup (revamped)

ecsite@field • bash

Tester

Task

Band

Data points

Include tips

Show best-practice tips

Verbose details

Include sub-steps & rationale

$ echo "Select tester, task, and band — then Generate."

Uses current cable from the Cable Library (VF & loss). Change it above in the Cable Library and regenerate.

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Frequency Presets & Cable Library

Presets (edit per test plan)

Use	Band	Span	Notes
Sweep	Low	698–806 MHz	Adjust to carrier spec
Sweep	Mid/High	1710–2200 MHz	Split if needed
Sweep	C‑Band	3700–3980 MHz	Use project UL/DL
PIM	700	705/720 tones	IM3 near 690/735
PIM	AWS	1730/1755	IM3 near 1705/1780
PIM	PCS	1870/1895	IM3 near 1845/1920

Current Cable — HL4RPV‑50‑CBAND

Frequency	Loss (dB/100ft)
700 MHz	1.64
1700 MHz	2.68
1900 MHz	2.85
2100 MHz	3.01
3800 MHz	4.16

VF = 0.88. Loss values editable in tools below.

Cable Library (edit & use in calculators)

Select cable

Velocity Factor (VF)

Attenuation points (MHz,dB/100ft per line)

Calculators below use the selected cable. Values are stored in your browser (localStorage). Use “Reset library” if the loss estimator shows 0—this restores HL4 defaults.

HL4RPV‑50‑CBAND pre‑filled Other cables: fill VF + loss

Interactive tools

Loss Estimator (uses selected cable)

Run length (ft)

Frequency (MHz)

Length ↔ Delay

Length (ft)

One‑way delay (ns)

Uses VF from selected cable; defaults to HL4RPV‑50‑CBAND (0.88).

RL ↔ VSWR converter

Return Loss (dB)

VSWR

dBc ↔ dBm @ carrier power

Carrier power per tone (W)

PIM level (dBc)

PIM level (dBm)

Assumes two equal tones.

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Frequency Presets & Cable Library

Presets (edit per test plan)

Use	Band	Span	Notes
Sweep	Low	698–806 MHz	Adjust to carrier spec
Sweep	Mid/High	1710–2200 MHz	Split if needed
Sweep	C‑Band	3700–3980 MHz	Use project UL/DL
PIM	700	705/720 tones	IM3 near 690/735
PIM	AWS	1730/1755	IM3 near 1705/1780
PIM	PCS	1870/1895	IM3 near 1845/1920

Current Cable — HL4RPV‑50‑CBAND

Frequency	Loss (dB/100ft)
700 MHz	1.64
1700 MHz	2.68
1900 MHz	2.85
2100 MHz	3.01
3800 MHz	4.16

VF = 0.88. Loss values editable in tools below.

Cable Library (edit & use in calculators)

Select cable

Velocity Factor (VF)

Attenuation points (MHz,dB/100ft per line)

Calculators below use the selected cable. Values are stored in your browser (localStorage). Use “Reset library” if the loss estimator shows 0—this restores HL4 defaults.

HL4RPV‑50‑CBAND pre‑filled Other cables: fill VF + loss

Interactive tools

Loss Estimator (uses selected cable)

Run length (ft)

Frequency (MHz)

Length ↔ Delay

Length (ft)

One‑way delay (ns)

Uses VF from selected cable; defaults to HL4RPV‑50‑CBAND (0.88).

RL ↔ VSWR converter

Return Loss (dB)

VSWR

dBc ↔ dBm @ carrier power

Carrier power per tone (W)

PIM level (dBc)

PIM level (dBm)

Assumes two equal tones.

Troubleshooting — quick flow

Pan diagram

Mini‑map: drag the box to pan; tap the track to jump.

Tip: drag the slider or swipe sideways to pan the diagram.

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Frequency Presets & Cable Library

Presets (edit per test plan)

Use	Band	Span	Notes
Sweep	Low	698–806 MHz	Adjust to carrier spec
Sweep	Mid/High	1710–2200 MHz	Split if needed
Sweep	C‑Band	3700–3980 MHz	Use project UL/DL
PIM	700	705/720 tones	IM3 near 690/735
PIM	AWS	1730/1755	IM3 near 1705/1780
PIM	PCS	1870/1895	IM3 near 1845/1920

Current Cable — HL4RPV‑50‑CBAND

Frequency	Loss (dB/100ft)
700 MHz	1.64
1700 MHz	2.68
1900 MHz	2.85
2100 MHz	3.01
3800 MHz	4.16

VF = 0.88. Loss values editable in tools below.

Cable Library (edit & use in calculators)

Select cable

Velocity Factor (VF)

Attenuation points (MHz,dB/100ft per line)

Calculators below use the selected cable. Values are stored in your browser (localStorage). Use “Reset library” if the loss estimator shows 0—this restores HL4 defaults.

HL4RPV‑50‑CBAND pre‑filled Other cables: fill VF + loss

Interactive tools

Loss Estimator (uses selected cable)

Run length (ft)

Frequency (MHz)

Length ↔ Delay

Length (ft)

One‑way delay (ns)

Uses VF from selected cable; defaults to HL4RPV‑50‑CBAND (0.88).

RL ↔ VSWR converter

Return Loss (dB)

VSWR

dBc ↔ dBm @ carrier power

Carrier power per tone (W)

PIM level (dBc)

PIM level (dBm)

Assumes two equal tones.

Troubleshooting — quick flow

Pan diagram

Mini‑map: drag the box to pan; tap the track to jump.

Tip: drag the slider or swipe sideways to pan the diagram.

References & manuals

Official public docs for the common handhelds your crews use.

Anritsu Site Master S331L — User Guide (PDF)
Anritsu Site Master S331E/S361E/S332E/S362E — User Guide (PDF)
Anritsu PIM Master MW82119B — User Guide (PDF)
Anritsu PIM Master MW82119B — Programming Manual (SCPI)
Keysight FieldFox — CAT (Cable & Antenna Test) Help
Keysight FieldFox Library — Manuals (all models)
Rohde & Schwarz Cable Rider ZPH — User Manual
VIAVI OneAdvisor 800 — Cable & Antenna Testing (Quick Ref)

Tip: keep offline copies of the PDFs on field tablets for bad coverage areas.

Quick‑Access Limits

Check	Band	Typical Threshold
Return Loss	Low/Mid/High	≥ 14 dB
Return Loss	C‑Band	≥ 21 dB
PIM (IM3) @ 2×20W	700/AWS/PCS	≤ −110 dBc

Replace with carrier‑approved limits for this site. These are placeholders.

Anritsu steps — Site Master & PIM Master

Site Master — Sweep

Shift → Cal/Setup → Cable List → HL4RPV‑50‑CBAND or custom (VF 0.88 + loss points).
Freq/Dist: set band start/stop: Low 698–806 · Mid/High 1710–2200 · C‑Band 3700–3980 MHz.
Points/Averaging: 551 (≥401), Avg 4–16; IFBW Auto or 1–3 kHz.
Cal → OSL at port; save cal (site/sector/band/date).
Measure RL; switch to DTF RL; distance = run + ~20%; markers; export S1P (if available) + PNG.

PIM Master — PIM

Select 700 / AWS / PCS; set tone pair within UL; power per plan (e.g., 2×20 W).
IM order = 3rd (IM3); show dBc and dBm.
Attach Low‑PIM load; self‑cal; residual ≤ −115 dBc.
Baseline → light flex/tap → (optional) power sweep; log worst IM3 and product frequency.
Pass/fail per plan (typical ≤ −110 dBc @ 2×20 W). Export CSV + PNG.

Frequency Presets & Cable Library

Presets (edit per test plan)

Use	Band	Span	Notes
Sweep	Low	698–806 MHz	Adjust to carrier spec
Sweep	Mid/High	1710–2200 MHz	Split if needed
Sweep	C‑Band	3700–3980 MHz	Use project UL/DL
PIM	700	705/720 tones	IM3 near 690/735
PIM	AWS	1730/1755	IM3 near 1705/1780
PIM	PCS	1870/1895	IM3 near 1845/1920

Current Cable — HL4RPV‑50‑CBAND

Frequency	Loss (dB/100ft)
700 MHz	1.64
1700 MHz	2.68
1900 MHz	2.85
2100 MHz	3.01
3800 MHz	4.16

VF = 0.88. Loss values editable in tools below.

Cable Library (edit & use in calculators)

Select cable

Velocity Factor (VF)

Attenuation points (MHz,dB/100ft per line)

Calculators below use the selected cable. Values are stored in your browser (localStorage). Use “Reset library” if the loss estimator shows 0—this restores HL4 defaults.

HL4RPV‑50‑CBAND pre‑filled Other cables: fill VF + loss

Interactive tools

Loss Estimator (uses selected cable)

Run length (ft)

Frequency (MHz)

Length ↔ Delay

Length (ft)

One‑way delay (ns)

Uses VF from selected cable; defaults to HL4RPV‑50‑CBAND (0.88).

RL ↔ VSWR converter

Return Loss (dB)

VSWR

dBc ↔ dBm @ carrier power

Carrier power per tone (W)

PIM level (dBc)

PIM level (dBm)

Assumes two equal tones.

Troubleshooting — quick flow

Pan diagram

Mini‑map: drag the box to pan; tap the track to jump.

Tip: drag the slider or swipe sideways to pan the diagram.

References & manuals

Official public docs for the common handhelds your crews use.

Anritsu Site Master S331L — User Guide (PDF)
Anritsu Site Master S331E/S361E/S332E/S362E — User Guide (PDF)
Anritsu PIM Master MW82119B — User Guide (PDF)
Anritsu PIM Master MW82119B — Programming Manual (SCPI)
Keysight FieldFox — CAT (Cable & Antenna Test) Help
Keysight FieldFox Library — Manuals (all models)
Rohde & Schwarz Cable Rider ZPH — User Manual
VIAVI OneAdvisor 800 — Cable & Antenna Testing (Quick Ref)

Tip: keep offline copies of the PDFs on field tablets for bad coverage areas.

Interactive terminal — guided setup (revamped)

ecsite@field • bash

Tester

Task

Band

Data points

Include tips

Show best-practice tips

Verbose details

Include sub-steps & rationale

$ echo "Select tester, task, and band — then Generate."

Uses current cable from the Cable Library (VF & loss). Change it above in the Cable Library and regenerate.

Acceptance workbook

Field	Value
Site / Sector / Ant ID
Cable Profile	HL4RPV‑50‑CBAND (VF=0.88)
Run Length
DTF Max Distance
RL Limits
PIM Tone Power
PIM Limits
Notes

CSV export works locally in the browser—no server needed.